CNC Configurations Sheets
Citizen Cincom
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! Put ...
Okuma P100 P200 P300 UNC Configuration
Okuma Configuration On the Okuma, pressing Control plus Reset (looks like /// on the key) should bring up the start menu for Windows. In the start menu you want to run, then enter "compmgmt.msc" and click ok. There should be a local users and groups ...
FTP - Fanuc 0i, 30i, 31i, 32i
Changing CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! ...
Haas Ethernet - UNC Intermediate Local Share Configuration
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (phone camera) original settings before making modifications! On Haas ...
Allen Bradley 9 Series Configuration
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications. Device ...
Sodick Mark-45 EDM Configuration
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! Hard ...
Siemens 840D Serial Configuration
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! Changing ...
Okuma P100, P200, P300 Serial Configuration
Okuma OSP100, OSP200, and OSP300 CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (phone camera) original settings ...
Milltronics Configuration
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! ...
Cincinnati 2100 Configuration
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (phone camera) original settings before making modifications! Baud ...
Haas Configuration
CNC Parameters Newer Haas Press SETNG to bring up the machine settings. Press right arrow until you get to I/O tab. Press WRITE/ENTER button (lower right corner of panel). Use left and right arrow to toggle between choices for each setting. Press ...
Yasnac MX3-LX3 Configuration
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (phone camera) original settings before making modifications! To set ...
Yasnac MX2-LX2 Configuration
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (phone camera) original settings before making modifications! To set ...
Yasnac MX1-LX2 Configuration
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (phone camera) original settings before making modifications! To set ...
Yasnac I80 Configuration Document
CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! Set the ...
Mitsubishi Meldas Configuration Cocument
CNC Parameters 2 to 2 - 4800 (baud) 3 to 1 (1 stop bit) 4 to 0 (no parity) 5 to 1 (even parity) 6 to 3 (8 data bits) 7 to 5 (any two characters ends transmission) 11 to 3 (DC Codes) 12 to 0 (no DC Code Parity) 13 to 3 (DC2/DC4 output) 14 to 1 (CR ...
Mazak TPlus Configuration Document
CNC Parameters I1 - 2 (4800 baud) I2 - 3 (2 stop bits) I3 - 0 (No parity) I5 - 3 (8 data bits) I6 - 3 (XON/XOFF handshaking) I7 - 0 (No DC CODE parity) I8 - 5 (IO wait time) I10 - 1 (EOB or EOR for terminator) I11 - 1 (CR/LF for EOB) I13 - 0 (ISO ...
Mazak T32 Configuration Document
CNC Parameters Parameters in column DV1 apply to CMT IO Parameters in column DV2 apply to TAPE IO I1 - 2 (4800 baud) I2 - 3 (2 stop bits) I3 - 0 (No parity) I5 - 3 (8 data bits) I6 - 3 (XON/XOFF handshaking) I7 - 0 (No DC CODE parity) I8 - 5 (IO wait ...
Mazak MPlus Configuration Document
CNC Parameters G1 - 1 (9600 baud) G2 - 3 (2 stop bits) G3 - 0 (even parity) G4 - 0 (Disable parity check) G5 - 3 (8 data bits) G6 - 1 (EOB or EOR as terminator) G9 - 1 (CR/LF for EOB) G10 - 3 (XON/XOFF handshaking) G11 - 0 (No DC Code parity) G12 - 0 ...
Mazak Matrix Configuration Document
CNC Parameters Tape I/O Parameters: Baud rate - 9600 Data bits - 8 Parity - None Stop Bit - 2 Hand Shake - DC CONTROL Wait Time - 5 Format - ISO Same Wno. - ALARM (or LOAD to overwrite) Port – COM3 (or other port as applicable) Extended TAPE ...
Mazak M32 Configuration Document
CNC Parameters G1 = 2 (CMT 4800 baud) G19 - 2 (EIA 4800 baud) G20 - 3 (2 stop bits) G21 - 0 (even parity) G22 - 0 (Disable parity check) G23 - 3 (8 data bits) G27 - 0 (CR/LF) G29 - 3 (XON/XOFF) G30 - 1 (No DC Code parity check) G40 - 0 (No DC2/DC4) ...
Mazak M2 Configuration Document
CNC Parameters OP2 - BIT 0=1 (ISO) (leave other bits alone) OP3 - 109 OP4 - 70 OP15 - 0 OP16 - 0 OP20 - 0 (No leader) OP21 - 0 (No space before programs) OP22 - 0 (No trailer) OP23 - 16 (4800 input baud) OP24 - 16 (4800 output baud) FactoryWiz DNC ...
Mazak Fusion/640 Configuration Document
CNC Parameters Tape / ISO Parameters: Baud rate - 9600 Data bits - 8 Parity - None Stop Bit - 2 Hand Shake - DC CONTROL Wait Time - 5 Format - ISO Same Wno. - ALARM (or LOAD to overwrite) Port - COM1 (or other port as applicable) CMT Parameters: Baud ...
FTP - Fanuc 0i, 30i, 31i, 32i Configuration Document
CNC Parameters Setting (HANDY) screen: I/O=9 (for FTP) System (Param) screen: System button Press >Screen button until Embedded appears. Select Embedded Select Common. Enter the IP address for machine, Subnet Mask, and Router IP if necessary. Select ...
FTP - Fanuc 0i Configuration Document
CNC Parameters Setting (HANDY) screen: I/O=9 (for FTP) System (Param) screen: System button Press >Screen button until Embedded appears. Select Embedded Select Common. Enter the IP address for machine, Subnet Mask, and Router IP if necessary. Select ...
Fanuc 32i Configuration Document
CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) System (Param) screen: 101 = 10000001 102 = 0 (RS232 DC code control) 103 = 11 (9600 baud rate) 12=19200, 10=4800, 9=2400, 8=1200 7=600 6=300 FactoryWiz DNC ...
Fanuc 31i Configuration Document
CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) System (Param) screen: 101 = 10000001 102 = 0 (RS232 DC code control) 103 = 11 (9600 baud rate) 12=19200, 10=4800, 9=2400, 8=1200 7=600 6=300 FactoryWiz DNC ...
Fanuc 30i Configuration Document
CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) System (Param) screen: 101 = 10000001 102 = 0 (RS232 DC code control) 103 = 11 (9600 baud rate) 12=19200, 10=4800, 9=2400, 8=1200 7=600 6=300 FactoryWiz DNC ...
Fanuc 21i Configuration Document
CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) System (Param) screen: 101 = 10000001 102 = 0 (RS232 DC code control) 103 = 11 (9600 baud rate) 12=19200, 10=4800, 9=2400, 8=1200 7=600 6=300 FactoryWiz DNC ...
Fanuc 21 Configuration Document
CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) System (Param) screen: 101 = 10000001 102 = 0 (RS232 DC code control) 103 = 11 (9600 baud rate) 12=19200, 10=4800, 9=2400, 8=1200 7=600 6=300 FactoryWiz DNC ...
Fanuc 18i Configuration Document
CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) System (Param) screen: 101 = 10000001 102 = 0 (RS232 DC code control) 103 = 11 (9600 baud rate) 12=19200, 10=4800, 9=2400, 8=1200 7=600 6=300 FactoryWiz DNC ...
Fanuc 18 Configuration Document
CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) System (Param) screen: 101 = 10000001 102 = 0 (RS232 DC code control) 103 = 11 (9600 baud rate) 12=19200, 10=4800, 9=2400, 8=1200 7=600 6=300 FactoryWiz DNC ...
Fanuc 16i Configuration Document
CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) System (Param) screen: 101 = 10000001 102 = 0 (RS232 DC code control) 103 = 11 (9600 baud rate) 12=19200, 10=4800, 9=2400, 8=1200 7=600 6=300 FactoryWiz DNC ...
Fanuc 16 Configuration Document
CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) System (Param) screen: 101 = 10000001 102 = 0 (RS232 DC code control) 103 = 11 (9600 baud rate) 12=19200, 10=4800, 9=2400, 8=1200 7=600 6=300 FactoryWiz DNC ...
Fanuc 15T Configuration Document
CNC Parameters Setting screen: Punch code- 1=ISO TV CHECK=0 OFF Under Service page: 0000 = xxx01000 (ISO) 0020 = 1 (Input device Foreground) 0021 = 1 (Output device Foreground) 0022 = 1 (Input device Background) 0023 = 1 (Output device Background) ...
Fanuc 15M Configuration Document
CNC Parameters Setting screen: Punch code- 1=ISO TV CHECK=0 OFF Under Service page: 0000 = xxx01000 (ISO) 0020 = 1 (Input device Foreground) 0021 = 1 (Output device Foreground) 0022 = 1 (Input device Background) 0023 = 1 (Output device Background) ...
Fanuc 11T Configuration Document
CNC Parameters Setting screen: Punch code- 1=ISO TV CHECK=0 OFF Under Service page: 0000 = xxx01000 (ISO) 0020 = 1 (Input device Foreground) 0021 = 1 (Output device Foreground) 0022 = 1 (Input device Background) 0023 = 1 (Output device Background) ...
Fanuc 11M Configuration Document
CNC Parameters Setting screen: Punch code- 1=ISO TV CHECK=0 OFF Under Service page: 0000 = xxx01000 (ISO) 0020 = 1 (Input device Foreground) 0021 = 1 (Output device Foreground) 0022 = 1 (Input device Background) 0023 = 1 (Output device Background) ...
Fanuc 10T Configuration Document
CNC Parameters Setting screen: Punch code- 1=ISO TV CHECK=0 OFF Under Service page: 0000 = xxx01000 (ISO) 0020 = 2 (Input device Foreground) 0021 = 2 (Output device Foreground) 0022 = 2 (Input device Background) 0023 = 2 (Output device Background) ...
Fanuc 10M Configuration Document
CNC Parameters Setting screen: Punch code- ISO TV CHECK=0 OFF Under Service page: 0000 = xxx01000 (ISO) 0020 = 2 (Input device Foreground) 0021 = 2 (Output device Foreground) 0022 = 2 (Input device Background) 0023 = 2 (Output device Background) 5001 ...
Next page