Cincinnati 2100 Configuration

CNC Parameters

You will need to verify all parameters listed below that correspond to your CNC control.  These parameters may not match your particular machine’s control.  Document (phone camera) original settings before making modifications!

Baud Rate: 9600

Parity: None

Data bits: 8

Stop bits: 1

DTR control = DISABLED

RTS control = HANDSHAKING

CTS control = ENABLED

DSR control = DISABLED

DSR SENSE = DISABLED

Click on COMMIT CHANGE to save changes.

FactoryWiz DNC Settings

Basic Communication

1.01- Port Type: Standard

1.11- Baud: 9600 1.12- Data Bits: 8

1.13- ASCII None

1.14- Stop Bits: 1

1.15- Handshake: RTS/CTS

 

Sending Options

2.11- Leader: Leave blank

2.12- Trailer: Leave blank

2.23- Skip lines that contain: Leave blank

2.31- Automatic timeout: 7

 

Receiving Options

3.11- Program identifier 1: (

3.12- Program Identifier 2:

3.21- Receive timeout: 3

3.31- Ignore data before first end-of-block: False

3.32- Ignore data after last end-of-block: False

 

Remote Commands

4.02- Request for file command: GET-

4.03- Request for file command (drip feed):

4:11- Request to save command:

 

Additional Notes

Changing CNC Parameters

To set up parameters:

Click on MORE

Click on SYSTEM CONFIGURATION

Click on CNC COM SETUP

Click on HARDWARE tab

Change parameters as needed.

Outputting CNC Programs

Click on HOME SCREEN

Click on PROGRAMS

Click on TRANSFER PROGRAM

Cursor to program that will be sent

Click on OUTPUT

Click on COM PORT

Click on START TRANSFER

 

Inputting CNC Programs

Click on HOME SCREEN

Click on PROGRAMS

Click on TRANSFER PROGRAM

Click on INPUT

Click on COM PORT

Click on START TRANSFER

 

Wiring Diagram

Pinout includes RTS/CTS Handshaking DB9 at machine

	DB-9 com port	Wire color	DB-9 CNC	Jumper?
	(Disconnected)	Shield	1
	2 (Receive Data)	Green	3 (Transmit Data)
	3 (Transmit Data)	Red	2 (Receive Data)
	5 (Signal Ground)	Black	5 (Signal Ground)
	7 (RTS)	Brown	8 (CTS)
	8 (CTS)	Blue	7 (RTS)
			6 (DSR) 1 (DCD) 4 (DTR)	JUMPER

 

Pinout includes RTS/CTS Handshaking DB25 at machine

	DB-9 com port	Wire color	DB-25 CNC	Jumper?
	(Disconnected)	Shield	1
	2 (Receive Data)	Green	2 (Transmit Data)
	3 (Transmit Data)	Red	3 (Receive Data)
	5 (Signal Ground)	Black	7 (Signal Ground)
	7 (RTS)	Brown	5 (CTS)
	8 (CTS)	Blue	4 (RTS)
			6 (DSR) 8 (DCD) 20 (DTR)	JUMPER

 

• Related Articles

• Cincinnati 850 Configuration Document

  CNC Parameters Machine Parameters for Dataline: Baud Rate = 4800 Parity = NONE Data Bits = 8 Stop Bits = 1 Protocol Level = 1 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 8 1.13- ASCII None ...

• Cincinnati 850Sx Configuration Document

  CNC Parameters Machine Parameters for Dataline: Baud Rate = 4800 Parity = NONE Data Bits = 8 Stop Bits = 1 Protocol Level = 1 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 8 1.13- ASCII None ...

• Cincinnati 900 Configuration Document

  CNC Parameters Machine Parameters for Dataline: Marriage Parameter: 150 = 0 (NO PARITY) 151 = 10 (4800) 152 = 0 (1 stop bit) FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 7 1.13- ASCII Even ...

• Haas Configuration

  CNC Parameters Newer Haas Press SETNG to bring up the machine settings. Press right arrow until you get to I/O tab. Press WRITE/ENTER button (lower right corner of panel). Use left and right arrow to toggle between choices for each setting. Press ...

• Moxa Configuration-Wizard (Wired)

  NPort 51xx Moxa Configuration NPort Windows Server 2019 and below or Windows 10 and below Driver Manager (WHQL certified) NPort Windows Server 2022 and above or Windows 11 and above Driver Manager (WHQL certified) Optional: NPort Search Utility You ...