Fanuc 15T Configuration Document

Fanuc 15T Configuration Document


CNC Parameters


Setting screen:
Punch code- 1=ISO
TV CHECK=0 OFF


Under Service page: 
0000 =  xxx01000 (ISO)

0020 = 1 (Input device Foreground)

0021 = 1 (Output device Foreground)

0022 = 1 (Input device Background)

0023 = 1 (Output device Background)


5001 to 1 (Device Select)
5002 to 2 (RS232 Device Select)
5110 to 3 (Device type DC Codes used)
5111 to 1 (1 stop bit) 
5112 to 10 (4800 baud)  11=9600, 9=2400, 8=1200 7=600 6=300


FactoryWiz DNC Settings

Basic Communication

1.01- Port Type: Standard

1.11- Baud: 4800

1.12- Data Bits: 7

1.13- ASCII Even

1.14- Stop Bits: 1

1.15- Handshake: XON/XOFF


Sending Options

2.11- Leader: %<10>

2.12- Trailer: %

2.23- Skip lines that contain: %

2.31- Automatic timeout: 7


Receiving Options

3.11- Program identifier 1: O

3.12- Program Identifier 2: :

3.21- Receive timeout: 3

3.31- Ignore data before first end-of-block: True

3.32- Ignore data after last end-of-block: True


Remote Commands

4.02- Request for file command: GET-

4.03- Request for file command (drip feed): DNC-

4:11- Request to save command: PUT-


Additional Notes

Changing CNC Parameters:


System (Param) screen:
To set parameters, move dial to MDI mode on machine. 
Press SETTINGS key. Change PWE (#8000) to 1. The CNC will alarm. 

Outputting CNC Programs:

To output a program, set the CNC to "edit" mode. Press the PROG key on the control panel.  Use the right arrow (Page) key until PUNCH appears. Press PUNCH, then Press THIS.


Inputting CNC Programs:

To input a program, set the CNC to "edit" mode. Press the PROG key on the control panel. Use the right arrow(Page)keys until READ appears. Press READ, then press ALL. 



Wiring Diagram

Pinout includes RTS/CTS Handshaking


DB-9 com port

Wire color

DB-25 CNC

Jumper?


(Disconnected)

Shield

1



2 (Receive Data)

Green

2 (Transmit Data)



3 (Transmit Data)

Red

3 (Receive Data)



5 (Signal Ground)

Black

7 (Signal Ground)



7 (RTS)

Brown

5 (CTS)



8 (CTS)

Blue

4 (RTS)





6 (DSR)

8 (DCD)

20 (DTR)

JUMPER







    • Related Articles

    • Fanuc 0T Configuration Document

      CNC Parameters (Phone camera) original settings before making modifications! Setting screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) Parameters screen: 0002 = 1xxxxxx0 (do not change values for x) 0552 = 10 (4800 baud rate) 9=2400, ...
    • Fanuc 0M Configuration Document

      CNC Parameters (Phone camera) original settings before making modifications! Setting screen: Punch code- 1=ISO TV CHECK=0 OFF I/O=0 (for Channel 1) Parameters screen: 0002 = 1xxxxxx0 (do not change values for x) 0552 = 10 (4800 baud rate) 9=2400, ...
    • Fanuc 6MA Configuration Document

      CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF Input Device 1=0 Input Device 2=1 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 7 1.13- ASCII Even 1.14- Stop Bits: 1 ...
    • Fanuc 6TA Configuration Document

      CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF Input Device 1=0 Input Device 2=1 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 7 1.13- ASCII Even 1.14- Stop Bits: 1 ...
    • Fanuc 6TB Configuration Document

      CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF Input Device 1=1 Input Device 2=1 Param screen: 311 = 00001001 340 = 2 341 = 2 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data ...